不銹鋼電梯門套避坑指南，教你怎么選今天給大家分享一下不銹鋼電梯門套的一些干貨。

　　A guide to avoiding pitfalls with stainless steel elevator door frames, teaching you how to choose. Today, I will share with you some dry tips on stainless steel elevator door frames.

　　①顏色：現代簡約風顏色選黑色噴砂啞光，黑色拉絲啞光細紋，深灰色噴砂啞光都可以，都是防指紋的，這幾個顏色做的也多，看著大氣。②厚度：板材厚度的話從平整度上來說市場上0.8mm厚都完全可以了，安裝上之后不會出現凹凸不平的情況。

　?、?Color: Modern minimalist style color options include black sandblasted matte, black brushed matte with fine lines, and dark gray sandblasted matte, all of which are anti fingerprint. These colors are also the most commonly used and look atmospheric Thickness: In terms of flatness, a thickness of 0.8mm on the market is sufficient for sheet thickness, and there will be no unevenness after installation.

　　③材質：材質的話室內家裝正常201都沒問題，顏色可選性多一些。201的硬度也高面上不容易有坑，家裝完全沒問題（浴室衛生間除外）。304雖然防銹能力好一些，但是材質偏軟，稍高，顏色可選性偏少，加工和運輸途中稍不注意容易磕碰有坑。

　?、?Material: If the material is used, indoor decoration can be done normally without any problems, and there are more color options available. The hardness of 201 is also high, and it is not easy to have pits on the surface, so there is no problem with home decoration (except for bathrooms and toilets). Although 304 has better rust prevention ability, the material is relatively soft, the price is slightly higher, the color options are limited, and slight carelessness during processing and transportation can easily cause scratches and dents.

　?、芗庸すに嚕喝缓缶褪羌庸すに嚤仨毷桥俨酃に囌蹚?，門套正面寬度在能蓋住墻縫的前提下盡量窄#一些，但并不是越窄越好，盡量不低于10mm，建議15mm~20mm。這個可以根據洞口尺寸的大小相應的調整。側面的話正常凸出墻面10mm，不低于這個尺寸，方便后期安裝踢腳線收口。⑤安裝：安裝工藝的話就是找的不銹鋼師傅，切45度對角安裝，側面陰角不要打膠。這個安裝工藝很關鍵，有些木工師傅也能安裝但是能裝和裝好就是另一回事了。安裝好之后洞口寬的話用木龍骨或木方撐一下中間的位置，防止結構膠當時沒干然后下垂。就是等到保潔的時候擔保坨臘坦境都可以了的重要找的。

　　④ Processing technology: Then the processing technology must be groove cutting and bending. The front width of the door frame should be as narrow as possible while covering the wall gap, but it is not necessarily the narrower the better. It is recommended to be no less than 10mm, and it is suggested to be 15mm~20mm. This can be adjusted according to the size of the opening. On the side, it is normal to protrude 10mm from the wall, preferably not less than this size, to facilitate the later installation of the skirting board closure Installation: In terms of installation process, it is recommended to find a professional stainless steel technician and install it diagonally at a 45 degree angle. It is best not to apply glue to the side corners. This installation process is crucial, and some carpenters can also install it, but being able to install and install it is another matter. If the opening is wide after installation, use wooden keel or wooden square to support the middle position to prevent the structural adhesive from not drying out and sagging. Finally, when it comes to cleaning, it's important to find a professional to ensure that the Tuola Tanjing is ready.

　　本文由 淄博電梯門套 友情奉獻.更多有關的知識請點擊   http://www.shsb373.cn  真誠的態度.為您提供為的服務.更多有關的知識我們將會陸續向大家奉獻.敬請期待.

　　This article is a friendly contribution from Zibo Elevator Door Frame. For more related knowledge, please click http://www.shsb373.cn Sincere attitude. We provide you with comprehensive services. We will gradually contribute more relevant knowledge to everyone. Please stay tuned